Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Culver City, CA
Culver City gate work splits into two very different jobs. Residential blocks still hold 1940s and 1960s bungalows whose driveway gates are now hitting their first major repair cycle, while the studio campuses along Washington Boulevard and the Hayden Tract run heavy commercial sliding gates with integrated access control that smaller shops can’t touch. That means the same technician might reset a keypad on a Clarke Drive courtyard gate in the morning and weld a roller bracket on a Jefferson Boulevard loading-dock gate by afternoon. Call (424) 380-7998 and you’ll get a live person who can tell you which one you’re dealing with.
Why Culver City Homes Are Different
Culver City sits three to four miles from the Pacific, and the marine layer that rolls through most mornings carries salt moisture onto gate hardware year-round. Steel rollers, hinge pins, and exposed wiring conduits corrode faster here than they do in Hawthorne or other inland blocks, and we see it most often on the swing gates added to Spanish Colonial Revival homes during the 2010s renovation wave. Those gates were often built with decorative wrought-iron frames and A/C-powered operators that were never rated for continuous salt-air exposure. In the Hayden Tract, the converted industrial buildings have an added wrinkle: heavy sliding gates with early-2000s operators that are reaching end-of-life in clusters, since multiple buildings were retrofitted around the same time. That creates a recurring wave of replacement calls a technician in Culver City will see far more often than anyone working a few miles east.
Our Main Culver City Services
Most Culver City calls fall into one of three categories, and each has its own page with pricing and sub-job detail.
Gate Repair in Culver City
Most residential repair calls in Culver City involve sagging swing gates, corroded hinge pins, or failed A/C-powered operators on 1940s-1960s homes. We write the price before any work starts and leave a photo record of every adjustment made. Gate Repair in Culver City
Gate Installation in Culver City
New gate installations in Culver City range from wrought-iron driveway swings on Spanish Colonial homes to heavy sliding gates for Hayden Tract industrial properties. Every install includes a written scope, a written price, and a documented record when the technician leaves. Gate Installation in Culver City
Gate Motor & Opener in Culver City
Operator failures in Culver City split between salt-corroded boards on residential swing gates and end-of-life sliding-gate motors on commercial properties. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule without steering you toward a replacement. Gate Motor & Opener in Culver City
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Culver City
Gate access control in Culver City means something different than it does in most cities. The studio and tech-media campuses along Washington Boulevard and the Hayden Tract run card-reader and keypad systems tied to vehicle barriers, and when one fails, the gate stops the lot, not just the driveway. That commercial demand means we see more integrated access-control service calls in Culver City than in any neighboring city, and our Gate Access Control work covers the same systems we document on every job: wiring diagrams, limit-switch readings, and a photo log left with the property manager or homeowner.
Keypad Entry
Signs you need it
Keypad codes stop working, the keypad doesn’t respond to new codes, or rust from marine air has corroded the wiring behind the keypad face.
What it costs in Culver City
Keypad replacement and wiring repair typically runs $265-$510 depending on whether the existing wire is salvageable or needs new conduit.
How we do it
We test the keypad output at the board, replace or re-terminate the wiring, program the new codes, and photograph the final settings.
Card Reader
Signs you need it
Cards read intermittently, the reader beeps but the gate doesn’t move, or the reader housing shows white salt corrosion around the mounting face.
What it costs in Culver City
Card reader replacement or reprogramming typically runs $340-$800, depending on whether you’re on Wiegand wiring or a newer encrypted reader.
How we do it
We identify the reader protocol, replace or re-seat the unit, verify every existing card against the new reader, and log the reader part number.
What Gate Access Control Costs in Culver City
| Item | Typical range in Culver City |
|---|---|
| Keypad entry replacement or repair | $265-$510 |
| Card reader replacement or reprogramming | $340-$800 |
| Phone entry or video intercom integration | $410-$1,150 |
Can a keypad be added to an existing gate in Culver City?
Yes. We tap the operator’s control board terminals, add a weather-sealed keypad, and run new low-voltage wire. The written price covers the keypad, wiring, programming, and the photo record before we leave.
Does Culver City require a permit for access control on a commercial gate?
Most commercial access-control changes fall under the city’s existing gate or barrier permit. We handle the scope and documentation so the written record matches what the city inspector will ask for. Call (424) 380-7998 to confirm your site.
Gate Parts & Welding in Culver City
Gate parts and welding in Culver City are driven by the salt air. Steel hinges, rollers, and post bases corrode faster three miles from the Pacific than they do ten miles inland, and the 2010s-era decorative gates on Spanish Colonial homes are now showing rust at exactly the points where the original installers used uncoated hardware. Our Gate Parts & Welding work covers both structural repair and custom fabrication, with the same written price and photo record on every visit.
Hinge Replacement
Signs you need it
The gate sags on the latch side, hinge pins have visible rust scale, or you can lift the gate a half-inch at the free end.
What it costs in Culver City
Hinge replacement typically runs $180-$390 per hinge, depending on post condition and whether we need to weld a new leaf to the frame.
How we do it
We cut or unbolt the old hinge, square the gate, weld or bolt the new hinge in place, and photograph the completed mount.
Gate Rollers
Signs you need it
The gate drags or squeals on its track, roller wheels show flat spots, or the gate jumps the track when fully open.
What it costs in Culver City
Roller replacement typically runs $160-$320 per roller assembly, with industrial sliding-gate rollers running higher on Hayden Tract properties.
How we do it
We measure the track profile, replace the roller and bracket, set the height so the gate travels level, and log the part numbers installed.
What Gate Parts & Welding Costs in Culver City
| Item | Typical range in Culver City |
|---|---|
| Hinge replacement (per hinge) | $180-$390 |
| Gate roller replacement (per roller assembly) | $160-$320 |
| Custom welding or frame reinforcement | $210-$650 |
Can you weld a broken gate frame on site in Culver City?
Yes, for wrought-iron and steel frames. We bring a portable welder, brace the gate square, weld the crack or replace the section, and photograph the repair. Call (424) 380-7998 for a written price.
How long do gate hinges last near the coast in Culver City?
Uncoated steel hinges in Culver City’s salt air typically last 5-8 years before rust pitting is significant. Powder-coated or stainless hinges last longer, and we stock both for same-day replacement.
Brands We Service in Culver City
We work on Linear, Viking, Ghost Controls, and DoorKing motors throughout Culver City, and carry common boards, remotes, and safety-edge parts in local stock so we’re not waiting on a distributor. Full brand coverage is on our brands page, including LiftMaster, FAAC, BFT, and Elite.
Pricing for Gate Repair in Culver City, CA
| Service | Typical range in Culver City |
|---|---|
| Gate access control (keypad, card reader, phone entry) | $265-$1,150 |
| Gate parts replacement (hinges, rollers, brackets) | $160-$650 |
| Custom welding or frame reinforcement | $210-$650 |
| Swing gate motor replacement | $450-$1,300 |
| Sliding gate operator replacement | $600-$2,500 |
| Photo-eye or safety-edge replacement | $180-$380 |
| Full residential gate installation | $1,900-$7,500 |
| Commercial sliding gate installation | $4,500-$18,000 |
Two things push prices up in Culver City: salt corrosion that requires replacing more than the failed part, and commercial Hayden Tract gates where access-control integration adds scope. Every price is written and handed to you before any work starts, so there’s no surprise invoice.
Neighborhoods We Serve in Culver City
We work across Culver City daily, from Clarkdale and Blanco-Culver Crest to McManus, Carlson Park, and Fox Hills. Response time for most Culver City calls is same-day or next-morning, depending on parts.
- Clarkdale
- Blanco-Culver Crest
- McManus
- Carlson Park
- Fox Hills
Service Area - Cities Near Culver City
We also serve Venice, CA, Inglewood, CA, Beverly Hills, CA, and Santa Monica, CA. Dispatch is coordinated from our Los Angeles office, and crews serve Culver City locally without routing through a distant hub.
Serving Culver City, CA - Our Local Coverage Area
We’re based in the Culver City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Culver City
Most Culver City calls get same-day or next-morning response, and a live person answers the phone 24/7. Commercial gate failures on Washington Boulevard or Hayden Tract properties get priority because a down gate stops the lot. Call (424) 380-7998 and describe the failure.
Most residential gate repairs don’t require a permit. Commercial properties with integrated access control or vehicle barriers may need city sign-off on changes. We document the work so the written record matches what an inspector will review.
Yes. We work with HOAs throughout Culver City, including communities in Fox Hills and Carlson Park, and we document every adjustment with photos and written part numbers so the board has a complete record. Estimates are free and written.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Culver City Customers Say
"The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A.