Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Hinge & Roller Replacement: The Inglewood Owner’s Guide
FAAC hinge and roller replacement in Inglewood typically runs between $240 and $520 installed, depending on which series gate you own and whether one or both hinges failed. We stock FAAC-specific hinge kits on the truck for the 400, 412, 770, and C720/C721 series, so most jobs are done the same day we arrive. What usually brings a homeowner to this page is a gate that’s started dragging on the opener end, sagging visibly at the free end, or grinding when it cycles.
Here’s the short version: FAAC operators are tough, but the hinges and rollers take every pound of the gate’s weight for years. When they wear out, the motor starts working harder, the gate drifts off the limit, and eventually the board overheats. The hinge set is the cheap fix. The motor is the expensive one. We’d rather replace the hinges before you’re buying a new control board.
Which FAAC Models This Applies To
We replace hinges and rollers on four FAAC swing-gate families common in Inglewood: the 400 series (typically the 412 and 422 compact operators), the 750/760/770 series, the C720/C721 commercial series, and the older 844/884 chain-driven units. Each uses a slightly different hinge geometry, and the roller diameter varies by gate weight class. A C721 hinge kit is not interchangeable with a 412 kit, and we’ve seen the wrong one forced on before, which wallows out the mounting holes and turns a $300 hinge job into a steel repair.
The fastest way to identify what you have is to check the motor housing label, which carries the series number. If the label is gone, we measure the gate leaf height and weight, then match the hinge pin diameter and roller spec to the table. For most Inglewood residential lots, a 10-to-14-foot leaf with a 7-inch roller is standard, but we carry the oversize rollers for wider, heavier leaves on corner lots. We install both OEM FAAC hardware and quality aftermarket equivalents when the OEM part is backordered, and we’ll tell you which one we’re quoting and why. Vance Gate Repair Inglewood is an independent service provider, not affiliated with FAAC, and we’ll put that in writing before any part goes on.
Signs Your FAAC Hinge & Roller Replacement Is Failing
- The gate sags at the free end and scrapes the driveway. This means the hinge pin or bushing has worn enough to drop the leaf. The roller is now carrying weight it was never designed to carry, and the scrape mark on the concrete is the giveaway.
- The gate jerks or shudders mid-travel. A flat-spotted or seized roller drags instead of rolling, so the leaf moves in fits. The operator is trying to compensate, and that’s rough on the limit switches.
- The opener runs but the gate barely moves. If the motor spins and the gate inches, the hinge friction or a collapsed roller is eating the torque. Left alone, this burns out the capacitor on residential FAAC boards.
- A clicking or popping sound when the gate reverses. That’s usually the hinge pin shifting inside a worn bushing. It’s metal-on-metal contact now, and the pin is being scored.
- The gate has shifted sideways, leaving an uneven gap at the latch post. Worn rollers allow lateral drift. The gate closes, but it doesn’t meet the latch the same way it did six months ago.
Most of these fail in pairs or as part of a chain reaction. One worn roller puts load on the opposite hinge, and six months later you’re doing both.
BeforeAfterReplacement Cost & What’s Included
In Inglewood, expect to pay roughly $240 to $340 for a hinge-and-roller kit installed on a single residential leaf, and $380 to $520 when both hinges on both leaves are done, or when we’re working on a heavier commercial C-series gate. The parts themselves run $60 to $140 per hinge depending on series and whether we use OEM or aftermarket. Labor is the rest, and it’s usually 60 to 90 minutes for a standard two-hinge leaf.
Every quote is written before we start, and the price you sign is the price you pay. We don’t do time-and-materials discovery pricing on a hinge job. The written scope includes the part number, photo documentation of the worn hardware, the torque spec we set on reassembly, and a year of coverage under our 365-Day Done Right Promise. If the replacement hinge loosens or the roller fails within that year, we make it right at no charge.
DIY or Call Us?
On most FAAC gates, the hinge and roller hardware is under the gate’s full weight, and for larger leaves that’s hundreds of pounds that needs to be supported before anyone unbolts anything. A gate that drops mid-repair can crush a hand or pin a body. We’ve been called to Inglewood driveways where a homeowner got the first bolt out, the leaf shifted, and suddenly the job wasn’t a one-person Saturday project anymore.
What you can reasonably do is identify that the hinge or roller is the problem, not the motor or board. Check for the sag, the scrape mark, the flat spot on the roller, the play at the hinge pin. If you want to have someone look at it before you commit, call (424) 380-7998 and we’ll send a technician with a written price, not an upsell. Having grown up around machinery that either worked or didn’t, the one thing Adrian Vance has always disliked is a guess. We don’t guess on gate hardware.
FAQs
On a properly maintained gate, expect six to ten years from an OEM FAAC hinge set, with rollers on the lower end of that range because they carry more grit. Inglewood’s dry-season dust works into the roller bearings, and gates that sit in full sun with no lubrication tend to lose rollers around year five or six.
In most cases no, because the failure is wear in a bushing or bearing surface, not something a weld builds back up. We can sometimes rebore and sleeve a worn hinge housing if the leaf itself is still true, but that’s usually on gates with custom steelwork where replacement hardware isn’t available. For most FAAC series, replacing the part is cheaper than machining.
A standard single-leaf hinge and roller swap takes 60 to 90 minutes on site. We schedule it as a one-visit job, and we carry the common FAAC hinge kits on the truck so there’s no waiting on a distributor unless you have an unusual series or a custom leaf.
We stock hinge and roller kits for the FAAC 400, 412, 770, and C720/C721 series, along with parts for LiftMaster, Mighty Mule, and Ghost Controls when we’re already on site. If your FAAC model is outside that range, we can typically have the correct kit within two to three business days and will tell you that in writing before you wait on us.
Get a Written Price for Your FAAC Hinge & Roller Replacement
If your gate is sagging, grinding, or not latching the way it used to, call (424) 380-7998. We’ll have a technician in Inglewood look at the hinges, name what failed, write the price down, and leave you a photo record of everything we touched before we drive off. That’s how we work on every gate, every time.
Written by Adrian Vance, Owner, Vance Gate Repair Inglewood at Vance Gate Repair Inglewood, serving Inglewood and nearby areas.