Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair Before & After in Inglewood, CA
Most gate repair companies tell you they do good work. We’d rather show you. The photo record below comes from actual jobs across Inglewood, from Morningside Park to the streets off La Brea. Every project follows the same routine: we photograph what we found, document what we changed, and hand you the proof before we leave. That’s been the standard at Vance Gate Repair since Adrian Vance started the company in 2014, and it’s written into every job we take under The Haven Standard.
Recent Transformations
Swing Gate Motor Replacement on a Sloped Driveway in Morningside Park
The homeowner called because the gate had stopped responding about two weeks prior. We found the old Mighty Mule motor had burned out after the arm bracket pulled loose and let the gate fight the motor on every cycle. The fix was a new LiftMaster operator, a re-anchored bracket, and reset limit switches. The gate now opens and closes in about 14 seconds with no strain on the arm. Full photo log left with the homeowner, including the old motor’s serial number.
Welded Repair on a Sagging Ornamental Iron Gate off La Brea Avenue
This one had been dragging for months, and the homeowner had gotten used to lifting the gate by hand to close it. The bottom hinge had torn clean off the post, and the gate’s weight had started bowing the top hinge. We welded a new hinge plate to the post, added a reinforcement gusset, and re-hung the gate with fresh hardware. Before we left, we photographed the weld from three angles and gave the homeowner a written record of the rod and plate stock we used.
Access Control Upgrade at a Light Commercial Lot off Century Boulevard
The property manager thought the operator was failing because the gate kept reversing for no reason. What we found was simpler: the photo-eye, the infrared beam that stops the gate if something crosses the path, was misaligned by roughly two inches after a trash bin bumped the post. We realigned the beam, replaced the worn keypad with a new DoorKing unit, and ran five full test cycles with the manager watching. The gate hasn’t false-reversed since, and the manager has the photo log from that visit on file.
Slide Gate Track Reset on a Rental Property in North Inglewood
The landlord called us after tenants reported the gate had come off its track during a windstorm. We found two shattered roller wheels and a track section that had shifted about half an inch out of alignment. We replaced the rollers, re-bedded the track, and adjusted the guide wheels so the gate rolls straight even in the kind of wind that comes through the Baldwin Hills gap. The landlord got a written price before we started and a photo record when we finished, same as every job.
Ghost Controls Operator Install Paired to an Existing Gate
The homeowners had a solid swing gate but were tired of getting out of the car every time they came home. We installed a Ghost Controls operator, added an exterior keypad, and wired a push-button release inside the garage. Total install took about five hours, and we programmed the open and close limits so the gate coasts to a stop instead of slamming. They got the written flat price before we touched a tool, and the documented photo record covers every wire connection behind the operator cover.
Limit Switch Reset on a Viking Operator
The gate looked like it was closing but never actually sealed the opening, which had the homeowner worried about a security gap at night. We found the limit switch was set 12 degrees past travel, so the operator thought it had hit an obstruction and reversed. We reset the switch, photographed the new position, and tested it eight times in a row. The gate now closes fully against the stop. This is the kind of fix that takes under an hour and is billed exactly as quoted.
Want Results Like These?
Every job shown above started with a phone call and a written price before any work began. If your gate is grinding, sagging, not closing, or just being stubborn, call (424) 380-7998. We’ll send a background-checked technician with a name and photo provided before arrival. You’ll get a flat, written quote, a documented photo record when the job’s done, and our 365-Day Done Right Promise on the finished work.
Written by Adrian Vance, Owner at Vance Gate Repair Inglewood, serving Inglewood since 2014.