Ghost Controls Gate Parts & Welding Nationwide

Ghost Controls Gate Parts & Welding in Inglewood: What to Know First

Ghost Controls gate parts and welding in Inglewood typically run $180-$680 depending on whether we’re replacing a hinge, welding a cracked post bracket, or fabricating a custom mount for an odd driveway. We’re an independent Ghost Controls service provider, which means we repair and weld what’s already on your property rather than steering you toward a full system replacement. Most parts-and-welding jobs are done same-visit, with a written price handed to you before any work begins and a photo record of everything we touched left on your phone or countertop.

Call (424) 380-7998

This page is for Inglewood homeowners who already own a Ghost Controls system and need the steel around it fixed, not the motor replaced. If your gate sags, drags, or won’t latch, call (424) 380-7998. A live person answers, and the estimate is free.

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls builds reliable swing-gate motors, but the gate hardware around them takes a beating in Inglewood’s sun, wind, and shifting soil. Here’s what we actually see on service calls, series by series.

• Rust-through at the hinge weld on the TSS1 and TDS1 series: Ghost Controls packages these as DIY kits, which means the original hinge plates are often thin-gauge powder-coated steel. Five or six years of Inglewood morning marine layer and afternoon heat cycles starts rust at the weld seam, where water pools. We cut out the rotted bracket, weld in a thicker 3/16-inch steel plate, and re-powder-coat the repair. The motor is fine; the mount is what failed.
• Gate-end bracket misalignment on the GTR-series (Ghost Controls single and dual gate openers): The post bracket you bolt to the gate moves under repeated load, especially on gates over 12 feet. The arm still pushes, but the bracket is now canted five or ten degrees, which wears the clevis pin and eventually snaps it. We realign or weld-reinforce the bracket, then recheck the limit travel so the motor isn’t fighting itself.
• Broken hinge pin or seized barrel on softer metal hinge sets used with DTP1 and TDS2 systems: Ghost Controls doesn’t ship the hinge; homeowners or installers source it locally, and not all hinge sets are rated for a 300-pound gate. We see sheared pins and egged-out barrels on gates that never got a service hinge upgrade. We replace with greasable steel barrel hinges and weld the bottom leaf to the post for shear load, not just bolt clamping.
• Chain-link and tube-gate sag that overloads the Ghost Controls arm: In Inglewood, the soil along Centinela Avenue and the neighborhoods east of Kia Forum shifts with winter rain and summer dry-down. A post that was plumb is now leaning 1 to 2 degrees. The gate sags, the opener arm binds, and the motor draws high current. We cut and re-weld the hinge post base, reset the post in new concrete where needed, and bring the gate back to plumb so the arm travels clean.
• Latch and lock failure on the pull-to-open Ghost Controls configuration: On pull-to-open, the latch side takes the full slam if the close limit isn’t set dead accurate. We see bent strike plates and broken spring latches. We weld in a reinforced strike plate and set the limit so the gate closes against the latch, not through it.

Our Ghost Controls Gate Parts & Welding Process

Here’s how a Ghost Controls parts-and-welding job runs when we’re on your driveway in Inglewood.

1. 1
   We listen, then we look. You’ll describe the symptom. We photograph the gate where it stands, hinges to latch to arm, and measure post plumb and gate level.
2. 2
   We name what we found. Before a grinder or a welder comes off the truck, you hear it in plain terms: “The hinge barrel is egged out about 4 millimeters. The pin is loose. The post is plumb.”
3. 3
   You get a written price. Haven Standard Clause 1: flat price, handed to you, before any work starts. That price covers the part, the weld, the grind, the paint, and the cleanup.
4. 4
   Parts decision, made with you. If an OEM Ghost Controls part is warranted, we use it. If an aftermarket steel part is stronger for the same or less money, we say so and show you the difference. No mystery parts.
5. 5
   We weld, replace, and set. The repair is done, then we run the motor through its travel and reset limits to the new geometry.
6. 6
   Documentation and guarantee. You get a photo log of what was found, what was set, and what was installed. The work is covered by our 365-Day Done Right Promise: if it isn’t right, we make it right, no argument, no fee.

Before

After

What Ghost Controls Gate Parts & Welding Costs in Inglewood

Here are the price ranges we quote most often for Ghost Controls hardware repairs in Inglewood. The written price you get before work starts is the exact price you pay.

• Single hinge replacement (weld-in): $180-$320 depending on gate weight and whether we need to reset the post.
• Gate bracket realignment and reinforcement: $220-$380, including re-welding the bracket and resetting travel limits.
• Cracked post or hinge plate repair: $250-$500 when the post itself needs cutting, reinforcing, or re-setting in concrete.
• Custom fabrication (odd driveway angle, new mount, gate extension): $340-$680, quoted line-by-line after we measure.
• Latch, lock, and strike plate repair: $120-$240 including welding in a new strike plate and setting the close limit.

What moves the price is gate weight, steel condition, whether the post needs concrete work, and whether we’re fabricating a part that doesn’t exist off the shelf. Not the brand name. Call (424) 380-7998 for a free estimate; you’ll get a specific number, not a range.

Why Inglewood Homeowners Call Vance Gate Repair Inglewood for Ghost Controls Work

We work on Ghost Controls systems the way Adrian Vance learned to work on commercial access control in New York: name what you found, name what it costs, name what you left behind. Every job gets a written price before tools come off the truck, and every job gets a photo record of the work before we leave. No verbal handshake, no surprise invoice, no re-diagnosing the same problem next year because nothing was documented.

We service Ghost Controls regularly, but we also service LiftMaster, Mighty Mule, and DoorKing. If your Ghost Controls gate has a metal failure today and you want a second opinion on the motor tomorrow, you don’t need a different company. The 365-Day Done Right Promise covers every repair we complete, and a live person answers the phone at (424) 380-7998 all day, every day.

FAQs